... | @@ -8,7 +8,7 @@ |
... | @@ -8,7 +8,7 @@ |
|
- **AIR EXHAUST & AIR ASSIST MUST BE ON BEFORE LASER OPERATION** and let them run for 5 seconds after the job is done before opening the lid
|
|
- **AIR EXHAUST & AIR ASSIST MUST BE ON BEFORE LASER OPERATION** and let them run for 5 seconds after the job is done before opening the lid
|
|
|
|
|
|
- **NEVER EVER LEAVE MACHINE UNATTENDED DURING OPERATION. NOT EVEN FOR 5 SECONDS.**
|
|
- **NEVER EVER LEAVE MACHINE UNATTENDED DURING OPERATION. NOT EVEN FOR 5 SECONDS.**
|
|
- **NEVER EVER LxEAVE MACHINE UNATTENDED DURING OPERATION. NOT EVEN FOR 5 SECONDS.**
|
|
- **NEVER EVER LEAVE MACHINE UNATTENDED DURING OPERATION. NOT EVEN FOR 5 SECONDS.**
|
|
- **NEVER EVER LEAVE MACHINE UNATTENDED DURING OPERATION. NOT EVEN FOR 5 SECONDS.**
|
|
- **NEVER EVER LEAVE MACHINE UNATTENDED DURING OPERATION. NOT EVEN FOR 5 SECONDS.**
|
|
- **NEVER EVER LEAVE MACHINE UNATTENDED DURING OPERATION. NOT EVEN FOR 5 SECONDS.**
|
|
- **NEVER EVER LEAVE MACHINE UNATTENDED DURING OPERATION. NOT EVEN FOR 5 SECONDS.**
|
|
- **NEVER EVER LEAVE MACHINE UNATTENDED DURING OPERATION. NOT EVEN FOR 5 SECONDS.**
|
|
- **NEVER EVER LEAVE MACHINE UNATTENDED DURING OPERATION. NOT EVEN FOR 5 SECONDS.**
|
... | @@ -19,9 +19,8 @@ |
... | @@ -19,9 +19,8 @@ |
|
# IN CASE OF FIRE
|
|
# IN CASE OF FIRE
|
|
- **hit the EMERGENCY STOP button**
|
|
- **hit the EMERGENCY STOP button**
|
|
- **shut down air assist and air exhaust**
|
|
- **shut down air assist and air exhaust**
|
|
- **SHOUT FOR HELP**
|
|
-**hit the emergency door open/fire alarm located next to the door to G11**
|
|
- **open the laser and if possible - remove the burning piece from the machine onto the concrete workshop floor**
|
|
- **RUN OUT SCREAMING FOR HELP**
|
|
- **either stomp out the fire or use the CO2 fire extinguisher located next to the machine**
|
|
|
|
|
|
|
|
|
|
|
|
## Operation modes:
|
|
## Operation modes:
|
... | @@ -53,7 +52,8 @@ |
... | @@ -53,7 +52,8 @@ |
|
|
|
|
|
|
|
|
|
## 3D Design Software:
|
|
## 3D Design Software:
|
|
- [123D Make](http://www.123dapp.com/make)
|
|
- [TinkerCAD ](https://www.tinkercad.com/) (web-based)
|
|
|
|
- [OnShape](https://www.onshape.com/)(web-based)
|
|
- [Pepakura](http://www.tamasoft.co.jp/pepakura-en/)
|
|
- [Pepakura](http://www.tamasoft.co.jp/pepakura-en/)
|
|
- [Fusion360](http://help.autodesk.com/view/fusion360/ENU/)
|
|
- [Fusion360](http://help.autodesk.com/view/fusion360/ENU/)
|
|
- [Surface unwrapping in Rhino3D](http://docs.mcneel.com/rhino/5/help/en-us/commands/unrollsrf.htm)
|
|
- [Surface unwrapping in Rhino3D](http://docs.mcneel.com/rhino/5/help/en-us/commands/unrollsrf.htm)
|
... | | ... | |